How to wire the starter buttion in my k&s Control
- alexromega
-
Topic Author
- Offline
- User
-
Registered
- first build and lovin it
- Posts: 69
- Thanks: 0
How to wire the starter buttion in my k&s Control
11 Jan 2017 12:29
I have a k&s Black Handlebar Start & Stop Control Switch
I am trying to figure out what wire goes where
I am trying to figure out what wire goes where
Attachment IMG_0410-2-3.JPG not found
Attachments:
Please Log in or Create an account to join the conversation.
- alexromega
-
Topic Author
- Offline
- User
-
Registered
- first build and lovin it
- Posts: 69
- Thanks: 0
Re: How to wire the starter buttion in my k&s Control
11 Jan 2017 12:41 - 11 Jan 2017 14:10
I also not using my old wiring harness. I have an m unit and this is going on a kz550
I believe the Y/R goes to my starter Solenoid and the Green/White is grounded.
I'm not sure how the engine stop and run is wired. If anyone could help me i the right direction
I believe the Y/R goes to my starter Solenoid and the Green/White is grounded.
I'm not sure how the engine stop and run is wired. If anyone could help me i the right direction
Last edit: 11 Jan 2017 14:10 by alexromega.
Please Log in or Create an account to join the conversation.
- loudhvx
-
- Offline
- KZr Legend
-
Registered
- Posts: 10864
- Thanks: 1618
Re: How to wire the starter buttion in my k&s Control
11 Jan 2017 16:22
It would probably help to keep this in your other thread so it all can be in one place.
How to wire the switch depends on how the solenoid is wired.
Post a diagram of how you have the solenoid wired so far. If you are using the M unit as a go-between, then you will have to follow the instructions for that.
If you want to simply wire the start function without the M unit, that is simple too.
How to wire the switch depends on how the solenoid is wired.
Post a diagram of how you have the solenoid wired so far. If you are using the M unit as a go-between, then you will have to follow the instructions for that.
If you want to simply wire the start function without the M unit, that is simple too.
1981 KZ550 D1 gpz.
Kz550 valve train warning.
Other links.
Kz550 valve train warning.
Other links.
The following user(s) said Thank You: alexromega
Please Log in or Create an account to join the conversation.
- alexromega
-
Topic Author
- Offline
- User
-
Registered
- first build and lovin it
- Posts: 69
- Thanks: 0
Re: How to wire the starter buttion in my k&s Control
11 Jan 2017 18:32
Yeah your right I should have but I wanted a fresh new start and mind set on this. I found some info on the solenoid, the solenoid I purchased has the two wires on them. The green/red and Y/R, turns out it doesn't matter. Both wires do the same, the g/r could go to the button or the y/r DONT MATTER.
Please Log in or Create an account to join the conversation.
- alexromega
-
Topic Author
- Offline
- User
-
Registered
- first build and lovin it
- Posts: 69
- Thanks: 0
Re: How to wire the starter buttion in my k&s Control
11 Jan 2017 18:34
I have the diagram from my old post. I definitely have the control switch wires wrong in the picture.
Attachment IMG_0412.JPG not found
Attachment IMG_0416-2.JPG not found
Attachments:
Please Log in or Create an account to join the conversation.
- alexromega
-
Topic Author
- Offline
- User
-
Registered
- first build and lovin it
- Posts: 69
- Thanks: 0
Re: How to wire the starter buttion in my k&s Control
11 Jan 2017 18:43 - 11 Jan 2017 18:48Attachment IMG_0414-2.JPG not found
I just hope my igniters is wired right.
Attachments:
Last edit: 11 Jan 2017 18:48 by alexromega.
Please Log in or Create an account to join the conversation.
Moderators: Street Fighter LTD