- Posts: 5359
- Thank you received: 109
Split cases, old KZ pro needed...
- mark1122
- Offline
- User
- Keep twisting it
Less
More
14 Apr 2012 18:10 #515796
by mark1122
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Replied by mark1122 on topic Split cases, old KZ pro needed...
i dont recall if there is a side play measurement. just measure everything that is listed, and if its all in spec u r good to go.
76 KZ, frame gusset work,1200CC.Ported by Larry Cavanaugh, 1.5mm.over intakes, Carron Pipe, ZRX12 rear end, and seat,96zx9 front end.
01 CBR600F4i Track bike.
Cobourg, Ont. Can.
~ ~ ~_@
~ ~ _- \,
~ (k) / (z)
Please Log in or Create an account to join the conversation.
- Garn
- Offline
- User
Less
More
- Posts: 265
- Thank you received: 13
14 Apr 2012 19:17 - 14 Apr 2012 19:18 #515812
by Garn
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
Replied by Garn on topic Split cases, old KZ pro needed...
I did read somewhere in a Factory manual that they adjust the end-float in shafts by a different thickness shim washers. Check existing gears for any rounding of drive pins, or their corresponding slots/holes), as this is where end-float will affect gear engagement.
1 x 73 Z1 (Jaffa), 74 Z1A, 76 Z900-A4
1 x 73 Yamaha TX500 & 98 fzx250 Zeal
Sydney Australia
Last edit: 14 Apr 2012 19:18 by Garn.
Please Log in or Create an account to join the conversation.
- notaduc
- Topic Author
- Offline
- User
Less
More
- Posts: 297
- Thank you received: 3
15 Apr 2012 15:58 #515957
by notaduc
1980 (mostly) KZ1000
Replied by notaduc on topic Split cases, old KZ pro needed...
I am still really hoping to hear from someone who has seen/dealt with cases that looked this way.
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- notaduc
- Topic Author
- Offline
- User
Less
More
- Posts: 297
- Thank you received: 3
18 Apr 2012 01:40 #516436
by notaduc
1980 (mostly) KZ1000
Replied by notaduc on topic Split cases, old KZ pro needed...
Went to see John Pearson today. He assures me that my cases look typical/fine...
He is very informative and friendly. Im happy to give him my business...
He is very informative and friendly. Im happy to give him my business...
1980 (mostly) KZ1000
Please Log in or Create an account to join the conversation.
- andy9802gt
- Offline
- User
- If it tastes that good, eat it yourself.
Less
More
- Posts: 704
- Thank you received: 18
18 Apr 2012 05:36 #516446
by andy9802gt
Told ya they were okay.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Replied by andy9802gt on topic Split cases, old KZ pro needed...
notaduc wrote: Went to see John Pearson today. He assures me that my cases look typical/fine...
He is very informative and friendly. Im happy to give him my business...
Told ya they were okay.
'78 KZ1075 LTD
stage 1 head by Larry Cavanaugh
race built crank by John Pearson
Mikuni rs34's
k410 cams
back cut tranny
8" over D&G swinger
proving once again that age and treachery is better than youth and enthusiasm
Please Log in or Create an account to join the conversation.