KZR's Bikes of the Month for 2024

First KZ project…. 1980 KZ1000

More
14 Nov 2016 10:00 #747946 by JOE MKII
Replied by JOE MKII on topic First KZ project…. 1980 KZ1000

swest wrote: You many not have to rebuild it. Pics of the dogs and gears? I did three just enough to raise the surface a little in those places. They should flatten out when compressed.
Steve

I will take some, they look good the tranny looks ok except for the bearing.
BUT I don't want problems later and seeing I got the bike for free sticking a few hundred into it seems ok to me. And undercutting my Suzuki tranny made a good difference it shifts nice and easy up or down,
The H2 I have you CANNOT get it into neutral unless its rolling but that is a strange beast anyway :lol: but it shifts really well with the undercut also.

I believe its called "Oppositional Defiance Disorder"

Please Log in or Create an account to join the conversation.

More
15 Nov 2016 04:24 #748000 by JOE MKII
Replied by JOE MKII on topic First KZ project…. 1980 KZ1000
Made a video, I don't know a lot about transmissions, this one looks good, no broken teeth engagement cogs look good ... except :

I believe its called "Oppositional Defiance Disorder"
The following user(s) said Thank You: bluezbike

Please Log in or Create an account to join the conversation.

More
15 Nov 2016 06:01 #748010 by 531blackbanshee
Replied by 531blackbanshee on topic First KZ project…. 1980 KZ1000
yeah,
that will be a problem. :pinch:
i have broken a bearing like that on my 80 z1r.but thats the first time i seen one of those gears do that. :sick:

leon

skiatook,oklahoma 1980 z1r,1978 kz 1000 z1r x 3,
1976 kz 900 x 3
i make what i can,and save the rest!

billybiltit.blogspot.com/

www.kzrider.com/forum/5-chassis/325862-triple-tree-custom-work

kzrider.com/forum/5-chassis/294594-frame-bracing?limitstart=0

Please Log in or Create an account to join the conversation.

More
15 Nov 2016 08:30 #748026 by floivanus
Replied by floivanus on topic First KZ project…. 1980 KZ1000
Output shaft may be damaged, kz transmission comes apart with a few snap rings, may be cheaper and easier to buy a good used output cluster. Make sure to get a 1980 chain drive output cluster, the gear widths on earlier trans gears are slightly different.

If you get a replacement output shaft you'll want to get it taken apart and at a bare minimum get the 2/5 gears checked to make sure the slots and dogs are fine, get them back-cut if you want.

my bikes; 80kz1000(project), 77 gl1000, 74 h2 (project)
Past; 78 kz1000, 83 kz550
Andrew

Please Log in or Create an account to join the conversation.

  • SWest
  • Offline
  • Sustaining Member
  • 10 22 2014
More
15 Nov 2016 16:33 #748053 by SWest
Replied by SWest on topic First KZ project…. 1980 KZ1000

Rendering Error in layout Message/Item: Kunena\Forum\Libraries\BBCode\KunenaBBCodeLibrary::renderEbayLayout(): Argument #1 ($ItemID) must be of type int, string given, called in /home/kzride5/public_html/libraries/kunena/src/BBCode/KunenaBBCode.php on line 314. Please enable debug mode for more information.

Please Log in or Create an account to join the conversation.

More
15 Nov 2016 16:45 #748054 by JOE MKII
Replied by JOE MKII on topic First KZ project…. 1980 KZ1000
You guys are ruining my day! :laugh: :laugh:
I was hoping it was just a bearing , then I thought maybe the gear… I know it not good.
I am going to send it in

I believe its called "Oppositional Defiance Disorder"

Please Log in or Create an account to join the conversation.

  • SWest
  • Offline
  • Sustaining Member
  • 10 22 2014
More
15 Nov 2016 17:00 #748055 by SWest
Replied by SWest on topic First KZ project…. 1980 KZ1000
No eBay APP ID and/or Cert ID defined in Kunena configurationIf it were me, I'd send in a working tranny not a damaged one. I got a low mile KZ 900 tranny, back cut it myself and it has over 20,000 miles on it now. I like this one. 17,000 miles? It's barely broken in. :whistle:
Steve
The following user(s) said Thank You: JOE MKII

Please Log in or Create an account to join the conversation.

  • SWest
  • Offline
  • Sustaining Member
  • 10 22 2014
More
15 Nov 2016 17:02 #748056 by SWest

Please Log in or Create an account to join the conversation.

More
15 Nov 2016 20:47 #748059 by rrsmsw9999
Replied by rrsmsw9999 on topic First KZ project…. 1980 KZ1000
I agree with Steve here, should be no problem and less expensive to find a good condition used output shaft and gears or full tranny. Looking at you video a good replacement unit should not leak where the cases are scuffed up a bit. R

1980 KZ 1000E2
Crashed 6/2016

1980 KZ550A
Sold 3/2016

Please Log in or Create an account to join the conversation.

  • SWest
  • Offline
  • Sustaining Member
  • 10 22 2014
More
15 Nov 2016 20:52 #748060 by SWest
Replied by SWest on topic First KZ project…. 1980 KZ1000
I just looked at the shipping, $83 is way too much.
Steve

Please Log in or Create an account to join the conversation.

More
16 Nov 2016 03:48 #748070 by JOE MKII
Replied by JOE MKII on topic First KZ project…. 1980 KZ1000
I am going to contact Robinson Industries again for more advice also.
I was told they stock most parts at reasonable prices, but check check and double check is always a good idea.

Thanks for the link Swest, shipping is a bit much but its a real nice part!! AND I too love spares!!
The other trannys on the bay are mostly from one seller in appleton Wi , not to far from me but I have been disappointed with parts from them in the past, but I have also gotten good parts from them, so its a mixed bag……. :unsure:

I believe its called "Oppositional Defiance Disorder"

Please Log in or Create an account to join the conversation.

More
29 Nov 2016 14:51 #749150 by JOE MKII
Replied by JOE MKII on topic First KZ project…. 1980 KZ1000
No eBay APP ID and/or Cert ID defined in Kunena configuration

swest wrote: If it were me, I'd send in a working tranny not a damaged one. I got a low mile KZ 900 tranny, back cut it myself and it has over 20,000 miles on it now. I like this one. 17,000 miles? It's barely broken in. :whistle:
Steve


Pulled the trigger on this item today, looks like a good deal at $187.00 shipped to my door, and spare parts!
Not a lot of sales for this seller but 100% rating, Crossing my fingers. I have had great e-bay deals mostly, but have also been completely ripped off, although e-bay does a good job standing by the buyer.
I will check it according to the manual , don't really think I need undercut gears I don't plan to beat this bike like I do the others just a good rider, now lets see if I can manage to ride it like that :unsure:

Thanks again Swest, extra eyes for parts is great!

I believe its called "Oppositional Defiance Disorder"

Please Log in or Create an account to join the conversation.

If you like KZR Please consider making a donation. Thank you.

KZRider is free, but not without cost.

Please consider chipping in a few bucks to help cover the cost of running the KZR servers.