Looking for carbs

More
18 Mar 2021 04:47 - 18 Mar 2021 04:50 #845132 by JR
Replied by JR on topic Looking for carbs
Open the throttle butterfly (engine side of carb), look in and up. Can you see anything resembling the 3 tiny holes circled in the pic below?  If so then these are pilot bypass holes and should be clear, Carb cleaner sprayed in the pilot jet should also come out here. They clog easily with dried gas residue etc 

 
1980 kz750E1, Delkevic exhaust
Last edit: 18 Mar 2021 04:50 by JR.
The following user(s) said Thank You: TexasKZ, Stumpy4u

Please Log in or Create an account to join the conversation.

More
18 Mar 2021 06:57 - 18 Mar 2021 06:59 #845133 by TexasKZ
Replied by TexasKZ on topic Looking for carbs
You should get a fine spray from each hole. Safety goggles are a good idea.

JR, he has mechanical slide carbs, so there is no butterfly.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
Last edit: 18 Mar 2021 06:59 by TexasKZ.
The following user(s) said Thank You: Stumpy4u

Please Log in or Create an account to join the conversation.

More
18 Mar 2021 11:33 #845157 by Stumpy4u
Replied by Stumpy4u on topic Looking for carbs
There are butterflies, and 2 of those holes on left side are blocked. And there is no spray, just liquid coming out of either side.  Getting ready for work right now, will try again tonight... After i get me a full face shield! And more carb cleaner, can almost empty and don't seem to have much pressure left.
1981 KZ305A CSR
Western Kentucky

Please Log in or Create an account to join the conversation.

More
18 Mar 2021 13:41 - 18 Mar 2021 13:46 #845165 by JR
Replied by JR on topic Looking for carbs
I used a small pin with the tip bent at 90 degrees to poke out mine. A first  (high E) guitar string bent appropriately should also work. I finished up with a good blast from compressed air line at a  gas station.

Whatever you use be gentle.

goid luck
1980 kz750E1, Delkevic exhaust
Last edit: 18 Mar 2021 13:46 by JR.
The following user(s) said Thank You: Stumpy4u

Please Log in or Create an account to join the conversation.

More
18 Mar 2021 14:49 - 18 Mar 2021 14:51 #845166 by F64
Replied by F64 on topic Looking for carbs
I use a welding tip cleaner. Just be careful. You don't want to enlarge the holes.
Honda makes a tool like this but it's a lot more than $10.
www.homedepot.com/p/Lincoln-Electric-Oxy...mers-KH575/100341101

A small brush set helps as well
www.harborfreight.com/airbrush-cleaning-...WEAQYCyABEgI1WPD_BwE


If you don't have an air compressor you could also use canned air to blow out to ports. Just grab a couple of cans because they can freeze up if you really use them. You can grab the other can while the frozen can warms back up.



 
81-KZ440-D2.
Louis Dudzik's GM HEI ignitor conversion installed 2015 s3.amazonaws.com/gpzweb/Ignition/GPZgmHEImod.html
Motogadget m-unit blue installed 2017.
LIC, NY
Attachments:
Last edit: 18 Mar 2021 14:51 by F64.
The following user(s) said Thank You: Stumpy4u

Please Log in or Create an account to join the conversation.

More
18 Mar 2021 19:42 #845184 by Kaylinator
Replied by Kaylinator on topic Looking for carbs
Expect to use 1 can of cleaner per carb. I can't tell you how many times I've told myself I don't need safety glasses before the carb cleaner went straight into my eyeballs. 
1978 KZ1000-A2
kzrider.com/forum/11-projects/613296-1978-kz1000-a2-barn-find

1978 KZ400-B1

2022 Z900RS SE

Please Log in or Create an account to join the conversation.

More
18 Mar 2021 21:44 #845190 by TexasKZ
Replied by TexasKZ on topic Looking for carbs
You can also use a guitar e string. They are really cheap. 
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough

Please Log in or Create an account to join the conversation.

More
19 Mar 2021 01:45 #845191 by Stumpy4u
Replied by Stumpy4u on topic Looking for carbs
Will I get that fine spray even if the mixture screw is backed way out, or does it need to be in the running position?
1981 KZ305A CSR
Western Kentucky

Please Log in or Create an account to join the conversation.

More
19 Mar 2021 06:36 #845195 by TexasKZ
Replied by TexasKZ on topic Looking for carbs
That shouldn’t matter. It would probably be better to completely remove the screws so that the threads get cleaned and so you can clean and inspect the screws. You can stick a thumb over the open hole.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
The following user(s) said Thank You: Stumpy4u

Please Log in or Create an account to join the conversation.

  • DOHC
  • Offline
  • Sustaining Member
  • Those Doe-Hawks really go!
More
21 Mar 2021 11:23 #845312 by DOHC
Replied by DOHC on topic Looking for carbs

Nothing like a face full of carb cleaner to make your day... 
​
 

I did that once.  I sprayed it into the idle jet hole/boss and it shot out the air-inlet port and straight into my eye.  Man did that hurt.  I flushed my eye with water for about 10 minutes before it started to feel sort of ok.  Definitely something to avoid!
'78 Z1-R in blue , '78 Z1-R in black, '78 Z1-R in pieces
My dad's '74 Z1
'00 ZRX1100

Please Log in or Create an account to join the conversation.

More
21 Mar 2021 15:49 #845320 by Stumpy4u
Replied by Stumpy4u on topic Looking for carbs
Ok, does anyone know what the "factory setting" is for the mixture screws?
1981 KZ305A CSR
Western Kentucky

Please Log in or Create an account to join the conversation.

More
21 Mar 2021 18:56 #845321 by JR
Replied by JR on topic Looking for carbs

Ok, does anyone know what the "factory setting" is for the mixture screws
 

According to the manual for the 82 305 the factory setting is 1 3/4 turns out.  your 81 is probably similar. I'd guess that  1.75 or 2 turns out from lightly seated is probably a good place to start.

If you need a manual you can download one here. Just click the "Articles" tab above and  check out service manuals in the drop down menu
1980 kz750E1, Delkevic exhaust
The following user(s) said Thank You: Stumpy4u

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum

Forum Links