- Posts: 36
- Thank you received: 0
Where do I use high heat gasket maker apose to normal?
- Buschpush
- Topic Author
- Offline
- User
- Forgive me if I sound dumb, new to this
Less
More
02 Jun 2024 15:19 #900122
by Buschpush
Where do I use high heat gasket maker apose to normal? was created by Buschpush
So I have a 1980/81 (not sure) kz250 LTD I have to ripped apart with new gaskets ready to do on but I'm planning on using a tiny thin layer of gasket maker as well as the new gaskets to make a better seal as the last owner messed with it and I see some tiny razor marks.
My question is what and where do I use high heat apose to normal?
I know on the hear gaskets to use high heat but what around the left side (alternator) or the right side (oil filters and such)
Thanks so much
My question is what and where do I use high heat apose to normal?
I know on the hear gaskets to use high heat but what around the left side (alternator) or the right side (oil filters and such)
Thanks so much
Please Log in or Create an account to join the conversation.
- Scirocco
- Offline
- Premium Member
- Never change a running system
Less
More
- Posts: 4208
- Thank you received: 2080
02 Jun 2024 20:18 #900129
by Scirocco
My 1975 Z 1 B 900 Project
www.kzrider.com/forum/11-projects/605133...ears-deep-sleep-mode
Replied by Scirocco on topic Where do I use high heat gasket maker apose to normal?
It´s not nessesary to use any kind of gasket maker on new gaskets.
Only if you are in the situation you have to use the old/used gasket again.
Only if you are in the situation you have to use the old/used gasket again.
My 1975 Z 1 B 900 Project
www.kzrider.com/forum/11-projects/605133...ears-deep-sleep-mode
The following user(s) said Thank You: Buschpush
Please Log in or Create an account to join the conversation.
- sf4t7
- Offline
- Sustaining Member
Less
More
- Posts: 565
- Thank you received: 373
02 Jun 2024 20:49 #900130
by sf4t7
Scotty
1974 Z1A
1015
welded Z1 crank
Andrews 1X Cams
Delkevic 4 into 1
Superbike bars
530 conversion
Replied by sf4t7 on topic Where do I use high heat gasket maker apose to normal?
If you are going to use the gasket maker, use the high heat one, it will work in either situation . No reason to have 2 different partial tubes on the shelf.
Scotty
1974 Z1A
1015
welded Z1 crank
Andrews 1X Cams
Delkevic 4 into 1
Superbike bars
530 conversion
The following user(s) said Thank You: Buschpush
Please Log in or Create an account to join the conversation.
- TexasKZ
- Away
- Platinum Member
Less
More
- Posts: 7581
- Thank you received: 2233
03 Jun 2024 06:25 #900150
by TexasKZ
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
Replied by TexasKZ on topic Where do I use high heat gasket maker apose to normal?
Some pictures of the damage may be helpful.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
Please Log in or Create an account to join the conversation.