- Posts: 60
- Thank you received: 0
Another Battery Topic!
- Sixgun
- Topic Author
- Offline
- User
I've got a couple questions on batteries. I've been checking the past posts and haven't quite found the answers I was looking for.
How long should your battery last? I know in cars they are rated by months, but does it work the same for bikes?
Lately I have been having issues with my battery providing enough oomph to start my '78 750. I've checked the voltage across the terminals.
Off 12.97
Idle 1000 rpm 12.85
3000 rpm 14.58
All the numbers seem in line. I can't figure out if I'm loosing charge or I just have a too weak battery. I bought the battery off smithgpz, a member from the old board. It's a sealed Yausa, but I know now they don't make a sealed one for the 750. It's 12Ah instead of 14Ah. Would this make a great difference on cranking power?
I did have to make a new negative battery cable a year or so ago. The old one was hanging on by a couple of strands. Seems tight and making good connection.
Any help will be greatly appreciated!
Thanks!
78 KZ750 B3
81 XS650SH
80 XS650G
Please Log in or Create an account to join the conversation.
- loudhvx
- Offline
- KZr Legend
- Posts: 10864
- Thank you received: 1615
It also depends on how much you maintain the battery, checking water, keeping it clean, etc.
Obviously the battery cables can affect starting as well as the starter solenoid. To check it, measure the voltage on the two big terminals on the solenoid while it's cranking (it'll take some alligator clips on the meter).
1981 KZ550 D1 gpz.
Kz550 valve train warning.
Other links.
Please Log in or Create an account to join the conversation.
- Sixgun
- Topic Author
- Offline
- User
- Posts: 60
- Thank you received: 0
I bit the bullet and went to batteries plus and had it tested. The battery read well on all tests until we put it under heavy load. It held for 5 seconds and went down. Gave it a couple of seconds, hit it again...same thing.
I'm still going to check all the connections now.
Thanks!
78 KZ750 B3
81 XS650SH
80 XS650G
Please Log in or Create an account to join the conversation.
- ltdrider
- Offline
- User
- Posts: 1232
- Thank you received: 17
I never took it out to check it, just pulled the side panel and looked at it. I thought I was looking at the water level, but it was just a shade line on the battery. So I got a new battery from Autozone, and now I pull the battery about every month (or so) and check the level.
Sixgun, your voltage numbers are just right, so your charging system is doing the job.
I usually kick start my bike when it's cold. It starts well with the kicker, and I think that saves the battery. Maybe it'll last longer that way. Also, I turn off the headlight when I start it. Don't forget to turn it back on!
'76 KZ900 LTD (Blaze)
'96 Voyager XII (Dark Star)
'79 KZ650 Cafe Project (Dirty Kurt)
Greensboro, NC
Please Log in or Create an account to join the conversation.
- KaZooCruiser
- Offline
- User
- Posts: 456
- Thank you received: 7
Clue was a battery that wouldn't crank the starter.
Started checking things with a multimeter. Battery is 12.2, so it's low, but has never run out of water. I had a kinked vent hose that didn't help things last year, when the gases destroyed my cable ends, but the bike still started and seem to run after all that was sorted out and repaired.
So I pull the sprocket cover as per manual, and on the 200v AC scale, I have 68v at 4000 rpm, which is below the 75v the output is supposed to be at the two yellow dynamo leads. It hits 75v at 5000rpm. The other tests regarding the 6 permanent magnet whizzy thingy seemed to be ok. Do I stop with this, or do I hope that a new battery thrown at the bike will be ok without dealing with this issue first. I suspect that if mine is magnetically decayed over time, I am going to have a hard time finding a good used one.
Please Log in or Create an account to join the conversation.
- OKC_Kent
- Offline
- User
- Posts: 1718
- Thank you received: 20
So I pull the sprocket cover as per manual, and on the 200v AC scale, I have 68v at 4000 rpm, which is below the 75v the output is supposed to be at the two yellow dynamo leads. It hits 75v at 5000rpm. .
You have two yellow leads? I thought we have three on the 650.
Nope you are right, two leads.:blink:
Post edited by: OKC_Kent, at: 2007/03/27 13:38
Oklahoma City, OK
78 KZ650 B2 82,000+ miles
Please Log in or Create an account to join the conversation.
- Sixgun
- Topic Author
- Offline
- User
- Posts: 60
- Thank you received: 0
I'm with you ltdrider. I usually kick start when the bikes cold. My issue happened earlier this morning when my bike died at a stop light. I tried the electric start...nada....then I kicked it and it decided to be stubborn. I had to pull to the side of the road and give her some attention before she'd start again...
Man I hate that.
78 KZ750 B3
81 XS650SH
80 XS650G
Please Log in or Create an account to join the conversation.
- edspring1
- Offline
- User
- Posts: 61
- Thank you received: 3
Please Log in or Create an account to join the conversation.
- Nevco48
- Offline
- User
- Posts: 579
- Thank you received: 3
The other tests regarding the 6 permanent magnet whizzy thingy seemed to be ok.
Show-off, gettin' all technical on us, aren't ya?
Please Log in or Create an account to join the conversation.
- loudhvx
- Offline
- KZr Legend
- Posts: 10864
- Thank you received: 1615
KaZooCruiser wrote:
So I pull the sprocket cover as per manual, and on the 200v AC scale, I have 68v at 4000 rpm, which is below the 75v the output is supposed to be at the two yellow dynamo leads. It hits 75v at 5000rpm. .
You have two yellow leads? I thought we have three on the 650.
Nope you are right, two leads.:blink:<br><br>Post edited by: OKC_Kent, at: 2007/03/27 13:38
77 had 3 (three phase)
After 77 they went to 2 (single phase)
Then later (early 80's?) they went back to 3.
1981 KZ550 D1 gpz.
Kz550 valve train warning.
Other links.
Please Log in or Create an account to join the conversation.