- Posts: 19
- Thank you received: 1
Sprockets
- ellwinger
- Topic Author
- Offline
- User
Less
More
11 Jul 2023 09:56 #887112
by ellwinger
Sprockets was created by ellwinger
My KZ650H runs great but tops out at 55 mph and 4000 rpm. That seems like the rpms are WAY to high and it needs to be geared down. Am I wrong?
Please Log in or Create an account to join the conversation.
- Wookie58
- Offline
- Moderator
Less
More
- Posts: 4180
- Thank you received: 2388
11 Jul 2023 10:01 #887113
by Wookie58
Replied by Wookie58 on topic Sprockets
When you say it “tops out” what do you mean? Are you saying it won’t go anymore in any gear?
Please Log in or Create an account to join the conversation.
- Nessism
- Offline
- Sustaining Member
Less
More
- Posts: 7461
- Thank you received: 2829
11 Jul 2023 11:00 #887117
by Nessism
Replied by Nessism on topic Sprockets
4000 rpm at 55 mph sounds about right. The engine is built to REV, so rev it and enjoy!
Please Log in or Create an account to join the conversation.
- ellwinger
- Topic Author
- Offline
- User
Less
More
- Posts: 19
- Thank you received: 1
11 Jul 2023 12:25 #887119
by ellwinger
Replied by ellwinger on topic Sprockets
Doesn't 55mph seem a little slow? It won't rev higher than that.
Please Log in or Create an account to join the conversation.
- Wookie58
- Offline
- Moderator
Less
More
- Posts: 4180
- Thank you received: 2388
11 Jul 2023 13:28 #887120
by Wookie58
Replied by Wookie58 on topic Sprockets
If it won't rev past 4000 then that is a totally different issue
Please Log in or Create an account to join the conversation.
- Nerdy
- Offline
- Sustaining Member
Less
More
- Posts: 1033
- Thank you received: 399
11 Jul 2023 13:56 #887121
by Nerdy
1979 KZ400 Gifted to a couple of nephews
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
Replied by Nerdy on topic Sprockets
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
The following user(s) said Thank You: sf4t7
Please Log in or Create an account to join the conversation.
- Nerdy
- Offline
- Sustaining Member
Less
More
- Posts: 1033
- Thank you received: 399
11 Jul 2023 13:58 #887122
by Nerdy
Could the ignition advancer be hanging up (i.e. not advancing)?
1979 KZ400 Gifted to a couple of nephews
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
Replied by Nerdy on topic Sprockets
If it won't rev past 4000 then that is a totally different issue
Could the ignition advancer be hanging up (i.e. not advancing)?
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
Please Log in or Create an account to join the conversation.
- Injected
- Offline
- User
Less
More
- Posts: 1071
- Thank you received: 583
11 Jul 2023 14:02 #887123
by Injected
Replied by Injected on topic Sprockets
A good running 650 four cylinder should "top out" at 110MPH @ 9000 RPM.My KZ650H runs great but tops out at 55 mph and 4000 rpm. That seems like the rpms are WAY to high and it needs to be geared down. Am I wrong?
The following user(s) said Thank You: ellwinger
Please Log in or Create an account to join the conversation.
- martin_csr
- Offline
- User
Less
More
- Posts: 8019
- Thank you received: 1645
12 Jul 2023 08:44 - 13 Jul 2023 08:00 #887148
by martin_csr
Replied by martin_csr on topic Sprockets
Assuming you have an 85mph speedometer, a 650-CSR should be able to peg the needle no problem with power to spare.
Make sure the battery is good and fully charged. I would do a load test.
Ignition coils. ride the motorcycle at speed, then stop & feel them. don't get burned by the valve cover.
The ignition coils should get warm, not hot. Mine were very hot to the touch, so I got new Dyna coils.
Clean, check & lubricate the timing advancer. make sure the springs & stuff are good and not rusted or damaged or anything.
Separate the rotor from the body while servicing & fill the groove w grease. Afterwards, operate the advancer by hand >> the rotor should snap back when released. This stuff is in the manual.
Make sure the battery is good and fully charged. I would do a load test.
Ignition coils. ride the motorcycle at speed, then stop & feel them. don't get burned by the valve cover.
The ignition coils should get warm, not hot. Mine were very hot to the touch, so I got new Dyna coils.
Clean, check & lubricate the timing advancer. make sure the springs & stuff are good and not rusted or damaged or anything.
Separate the rotor from the body while servicing & fill the groove w grease. Afterwards, operate the advancer by hand >> the rotor should snap back when released. This stuff is in the manual.
Last edit: 13 Jul 2023 08:00 by martin_csr.
Please Log in or Create an account to join the conversation.
- TexasKZ
- Offline
- Platinum Member
Less
More
- Posts: 7581
- Thank you received: 2234
12 Jul 2023 08:47 #887149
by TexasKZ
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
Replied by TexasKZ on topic Sprockets
Has all of the routine maintenance listed in the owner’s manual and the factory service manual been performed recently? If you are not 100% sure about any item on the list, I would start at the top and do each and every item as listed. In the process, you are quite likely to find the problem, and when you finish the list, you can be sure the bike is performing as designed. Following the schedule will insure that you have a well-running, reliable ride.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
The following user(s) said Thank You: Wookie58
Please Log in or Create an account to join the conversation.
- ellwinger
- Topic Author
- Offline
- User
Less
More
- Posts: 19
- Thank you received: 1
14 Jul 2023 20:12 #887225
by ellwinger
Replied by ellwinger on topic Sprockets
Advancer works great. seems like it gets no gas above 55.
Please Log in or Create an account to join the conversation.
- ellwinger
- Topic Author
- Offline
- User
Less
More
- Posts: 19
- Thank you received: 1
14 Jul 2023 20:15 #887226
by ellwinger
Replied by ellwinger on topic Sprockets
Everything checks out. Doesn't seem to be getting enough gas above55.
Please Log in or Create an account to join the conversation.