TOPIC:

That is just the icing on the cake....it complements your bike so well, really cool

nice very nice !

leon

I'd lovea sound clip, I'll bet it's LOUD

DesertKZ wrote: I'd lovea sound clip, I'll bet it's LOUD

I'll post one when I get it all bottoned up. Give me some time, I need to go back through my carbs and get my O2 sensor mount sorted.

I know you're on the road alot but it sure would be nice to see your 1075 kit installed!! Hope your doing well-Thanks for the great thread, Scott

fitscott wrote: I know you're on the road alot but it sure would be nice to see your 1075 kit installed!! Hope your doing well-Thanks for the great thread, Scott

Scott,
I'm working my way toward that. There is on more little electronic bit that I haven't shown yet which I want to install first. It will allow me to do some baseline testing prior to the 1075 kit. It's all part of my plan, but there has just been a big delay in the middle. I'll get there.

chugga chugga chugga chugga choo choo!!!!!!!!!!!!!!!!!!!!!!

keep at it when you can sir,
we can't wait to see the results.

leon

531blackbanshee wrote: chugga chugga chugga chugga choo choo!!!!!!!!!!!!!!!!!!!!!!
leon

That's kinda what it sounds like when you ease away from a stop right now. I guess I still have some stuff in two of my pilot circuits. I went ahead and ordered new air bleed jets, pilot air needles, jet block gaskets, and choke rod rubber seals to make sure everything in the carbs is as new as I can get.

It wasn't a problem before, so I'm sure there is a little bit of the green stuff stuck in two of the pilot passages. Runs fine once you get past the pilot circuits.

I got one exaust collar that was too small, so I can't run it yet. Chris is going to overnight me a new one. I can't wait to hear the new pipe!!!

once you get them carbs sorted and your new header installed we won't be able to wipe the smile off your face.

leon

Hi,

Have you had a chance to hear the pipe yet? I am ready to order one but I'm worried that it will be too loud. I am torn between the motogpwerks and the Vance and Hines. I plan to do some touring so an overly loud pipe can bother after a few hours of riding.

531blackbanshee wrote: once you get them carbs sorted and your new header installed we won't be able to wipe the smile off your face.

leon

Yep, and there is more to come, I'm just waiting on a few bits to show up on my doorstep.

Last night I pulled the carbs, and to my surprise, my son asked to help me out. I had to pull the old Fred Sanford heart attack routine since he never wants to help me with these kind of things. We confirmed what I was thinking. Number 2 and 4 had clogged pilot jets again. I went ahead and pulled the carbs completely apart for a comprehensive cleaning. I don't want to clean out the jets only to have this happen again.

GIFSoup

it's the BIG one!!!!!!!!!!!!!

leon

testarossa wrote: Well I couldn't stand it, so I started trying to fit the new pipe. I knew there would be some considerations due to the custom nature of my bike, but it actually fits pretty close. I need to make a slight mod to my rearset adapter plate so I can tilt it forward a touch. Then I will need to drill and tap the rearset for a stud to attach the tab on the tailpipe. That should just about do it. Obviously, I'm doing this to get the pipe as tight to the frame as possible. I cannot afford to have the pipe hanging too low. Thankfully the pipe crosses over the middle of the frame instead of running down the right side of the frame like my other exaust. I should actually have some cornering clearance on right handers now!

Here's what happened to my old pipe when I tried to go into a right hand turn very hard:

Attachment IMG_0857.JPG not found

And a couple of shots of the bike with the new exaust test fitted. Sorry about the poor lighting, the sun went down before I got done.

Attachment IMG_0855.JPG not found

Attachment IMG_0856.JPG not found

Now I just need to make a couple of tweaks to gain a bit of ride height, and the bike will sit perfect.

I was looking at getting that exhaust but I don't think it will clear the larger oil pan I have. I like the stainless look too.

Hollywoodmx wrote: I was looking at getting that exhaust but I don't think it will clear the larger oil pan I have. I like the stainless look too.

You are probably right about that. The collector passes directly under the oil filter bolt. You have a little wiggle room depending on the rear mount, but not much. I intentionally have mine as tight to the frame as possible. I'm clearing the oil filter bolt by about 1/4" with a standard oil pan.

Maybe an update on the sound?

infanterene wrote: Maybe an update on the sound?

It's real quiet right now.

Do you have more or less ground clearance with the new pipe. Not corning clearance but lowest part of pipe to ground. Thanks
Wayne

kzz1king wrote: Do you have more or less ground clearance with the new pipe. Not corning clearance but lowest part of pipe to ground. Thanks
Wayne

The new pipe has about 1/2" less ground clearance when the bike is straight up. It has to clear the oil filter bolt. The old pipe ran down the right frame rail.

infanterene wrote: Maybe an update on the sound?

Ok I have my carbs back together again and was able to ride around the neighborhood between thunderstorms. This pipe is definitely louder than my old exhaust. Quite the growl above 4000rpm. I'm not sure it's the best exhaust for touring. It's rather short so I may heat your bags if you are carrying any.

It's perfect for my needs. I took a quick video that I will try to post later.

Sorry to be a PIA! Thanks for the update. Im not really worried about bags as Ill probably only use a tank bag and/or tail bag. I am mostly concerned with noise level at a steady 65-75 cruise.

Your bike is looking awesome.