The Budweiser Burnout Bike Nascar style
I have seen it live twice its pretty cool.






[youtube][/youtube]

racer54 wrote:


yup, what he said.... ....

rolling burnouts are asking for trouble....just ask my bro....sold him my 85 gs1150e with the big bore kit.....he was leaving 25 feet of rubber in front of the local stealership.....funny....wasnt so funny when he tried it in april with a cold tire and it got all all squigly and he dumped it and screwed up a couple of toes on each foot when they got between the pegs and the road.....wasnt pretty...

keith1 wrote:skinny little hard compound rear tire aint gonna hurt nothin,now backflipping in 1st gear might be a bit of an issue!

Where you do it also makes a difference. Tried it once on concrete....found out why they like concrete launch pads at the strip. Man...that stuf had hooks. Out in front of the house on the tar and gravel road, now that's another story. You can get a bike with 1 hp smoking that tire. Looks impressive but can get exciting when using that "skinny little hard compound rear tire". Besides...he said he wanted to learn how to do wheelies, didn't he?

i always do my burnouts in second gear never hurt anything yet, start by getting the rear tire wet then grab the front brake with a couple of fingers and start rolling the throttle on at the same time snap the clutch out as the tire starts to bite you must get the throttle turn fully open. practice the movements with out every trying the actual burnout until they come natural to you the reason why i use second gear is higher wheel speed less time bagging the motor for the same result. remember go full throttle as quick as you can if you have a rev limiter. once you do a few it will become second nature. if fact i used to do so many burnouts i used to measure my summer of riding not by miles but in how many tires i went thru. as far wheelies go iuse a wheelie bar so that tells you i don't like them or do them.

Old Man Rock wrote:
Thats why I told him to have a friend there with a camera.

Yup, love thata third clip...

Let go Plummen, Let go of the damn bars....

No crap its like pull the clutch in dude.

thompsonmx100 wrote:
How could he pull in the clutch? The bike's dragging his ass across the lot.

The truth of the matter is that stunting, like racing is expensive. Little faux pas like these are every day shiite, when you're prepared, which is never the case on the street or in a parking lot.

KZCSI

isnt that how most wheelies are done,completely by accident?

all 3 of mine were accidental, and I sure as hell didn't look cool

"all 3 of mine were accidental, and I sure as hell didn't look cool "....

Especially when he BROWN stained his skivies...

Old Man Rock wrote:
You got it! I found out the hard way that kz1000's have a tad more torque than 550's.

I did that recently on my buddies ZRX. Basically gave it the same throttle that I would normally give my 750. When the front wheel was 2 feet off the ground I just about lost it but let of the throttle in time. A few friends were behind us in a car and I am sure I did not look cool!!

Like people have been saying, unless you have the experience to the point that the mechanics of riding come naturally and you're ready to spend some money, don't do it. That being said, if you really want a wheelie there are a few useful tips depending on what kind of bike you're on. When going for the lift, let off the throttle more or less completely so the weight of the bike shifts forward and preloads the front end. Then as it begins to pop back up, roll on the throttle (obviously depending on what bike you're on you're going to want to alter the amount of throttle you give it). Easiest and most controllable gear to do a slowish wheelie in is second but it depends on the bike and the rider. Oh, and make sure you keep your foot on the back brake so you can control your loft and kill it if you need to, the first couple of times its natural to drop your feet off the pegs (if only in shock ).

As far as burnouts go, I haven't done many stationary burns on high power bikes and as you've seen, they can go wrong easy. Rolling burns are fun and look pretty cool (until you dump the bike) but its very easy for them to get very squirrelly. Don't do 'em on cold tires and the easiest surface to do it on is tarmac with a scattering of gravel on it. Just take off slow and crank on the throttle and the tire'll break loose.

Good luck!

Its Dec, and i just had to get in 1 more ride before i tare my bike apart again.

mark1122 wrote:

Ride it like ya stole it!!!!!!!

show off! weve gotten 3" of flakey white stuff in last 24 with another 6-9 supposed to be here by tonight,ill do a burnout in my van today as im plowing through the snow drifts today!

I am not looking forward to the snow, but i did get my first snow blower. i have to keep the rev's varied to break it in,How do i do that, then change the oil.
Always something to look forward to.